Prontuario informatico hormigon 3.1: A user-friendly software that replaces and expands the collections of diagrams for concrete structural design
Prontuario informatico hormigon 3.1: A useful tool for concrete structural design
Are you looking for a software that can help you with the analysis, calculation and design of concrete structures according to the Spanish code EHE-08? If so, you might want to check out prontuario informatico hormigon 3.1, a free and user-friendly tool that can assist you with your projects.
prontuario informatico hormigon 3.1
Download Zip: https://www.google.com/url?q=https%3A%2F%2Furlcod.com%2F2tWU4P&sa=D&sntz=1&usg=AOvVaw2C-ChKnPY8F9TXgyyuK-S7
Introduction
Prontuario informatico hormigon 3.1 is a software developed by FHECOR Ingenieros Consultores with the collaboration of professors from Universidad Politécnica de Madrid and Universidad de Castilla-La Mancha. It is an adaptation of the previous versions of prontuario informatico del hormigon estructural, which were first presented in the 1980s.
The main objectives of this software are to replace and expand the collections of diagrams and to help students and engineers learn and apply the concepts and methods of concrete structural design. The software is based on the Spanish code EHE-08, which regulates the design, construction and maintenance of concrete structures.
The software is available for free download from the website of Instituto Español del Cemento y sus Aplicaciones (IECA). It is compatible with Windows operating systems and requires Microsoft Excel to run. The installation process is simple and fast, and the user interface is intuitive and easy to navigate.
Basic concepts of concrete structural design
Before using prontuario informatico hormigon 3.1, it is important to have some background knowledge on the basic concepts of concrete structural design. In this section, we will briefly review some of these concepts.
Concrete is a composite material made of cement, water, aggregates and admixtures. It has high compressive strength but low tensile strength, which means it can resist loads that tend to squeeze it but not those that tend to stretch it. To overcome this limitation, concrete is usually reinforced with steel bars or wires that can carry tensile forces.
Concrete structures can be classified into two main types: reinforced concrete (RC) structures and prestressed concrete (PC) structures. RC structures use passive reinforcement, which means that the steel bars only resist tensile forces after cracks have formed in the concrete. PC structures use active reinforcement, which means that the steel wires are tensioned before or after casting the concrete, creating a compressive stress that reduces or eliminates cracking.
Concrete structures can be used for various applications, such as buildings, bridges, dams, tunnels, foundations, etc. The design of concrete structures involves determining the dimensions, shape, reinforcement and details of each structural element according to the loads, constraints and requirements of each project. The design process must ensure that the structure is safe, serviceable, durable and economical.
How to use prontuario informatico hormigon 3.1
Prontuario informatico hormigon 3.1 is a software that can help you with the analysis, calculation and design of concrete structures according to EHE-08. In this section, we will explain how to use it step by step.
How to create a new project and input data
To start using prontuario informatico hormigon 3.1, you need to create a new project by clicking on the "Nuevo proyecto" button on the main menu. You will be asked to enter some basic information about your project, such as name, description, author, date, etc.
Then, you need to input data for each structural element that you want to analyze or design. You can choose from different types of elements, such as beams, slabs, columns, walls, foundations, etc. For each element, you need to enter its geometry (length, width, height), material properties (concrete class, steel type), loads (permanent, variable), reinforcement (area, diameter), etc.
You can input data manually by typing in values or selecting options from drop-down menus or buttons. You can also import data from Excel files by clicking on the "Importar datos" button on each element's window. You can also copy data from one element to another by clicking on the "Copiar datos" button.
How to perform analysis, calculation and design of concrete structures
After inputting data for each element that you want to analyze or design, you need to perform analysis, calculation and design by clicking on the "Calcular" button on each element's window. The software will perform different types of analysis, calculation and design depending on the type of element, such as:
Bending analysis, calculation and design for beams
Solid slab analysis, calculation and design for slabs
Punching shear analysis, calculation and design for slabs
Axial load analysis, calculation and design for columns
Biaxial bending analysis, calculation and design for columns
Shear wall analysis, calculation and design for walls
Bearing capacity analysis, calculation and design for foundations
Etc.
The software will apply the methods, criteria and formulas specified in EHE-08 for each type of analysis, calculation and design. The software will also check the compliance with the limit states of safety, serviceability, durability and fire resistance.
How to interpret and export results and reports
After performing analysis, calculation and design for each element, you can view the results and reports by clicking on the "Resultados" button on each element's window. You will see different types of results and reports depending on the type of element, such as:
Bending moment diagrams, shear force diagrams, deflection diagrams for beams
Solid slab diagrams, stress contour plots, reinforcement distribution plots for slabs
Punching shear diagrams, critical perimeter plots, reinforcement detail plots for slabs
Axial load diagrams, interaction diagrams, reinforcement detail plots for columns
Biaxial bending diagrams, interaction surfaces, reinforcement detail plots for columns
Shear wall diagrams, stress contour plots, reinforcement distribution plots for walls
Bearing capacity diagrams, settlement plots, reinforcement detail plots for foundations
Etc.
You can zoom in or out, pan or rotate the diagrams or plots by using your mouse or keyboard commands. the scale, color or style of the diagrams or plots by clicking on the "Opciones" button on each element's window. You can export the results and reports to Excel files by clicking on the "Exportar resultados" button on each element's window. You can also print the results and reports by clicking on the "Imprimir resultados" button on each element's window.
Examples of concrete structural design using prontuario informatico hormigon 3.1
To illustrate how to use prontuario informatico hormigon 3.1, we will present three examples of concrete structural design for different types of elements: a reinforced concrete beam, a prestressed concrete slab and a reinforced concrete column.
Example 1: Design of a reinforced concrete beam
In this example, we will design a simply supported reinforced concrete beam with a span of 6 m, a rectangular cross-section of 300 mm x 500 mm, a concrete class of C25/30 and a steel type of B500S. The beam is subjected to a permanent load of 10 kN/m and a variable load of 20 kN/m.
To design this beam using prontuario informatico hormigon 3.1, we need to follow these steps:
Create a new project and input the basic information about the project.
Select "Vigas" from the main menu and input the geometry, material properties and loads for the beam.
Click on "Calcular" to perform bending analysis, calculation and design for the beam.
Click on "Resultados" to view the bending moment diagrams, shear force diagrams, deflection diagrams and reinforcement detail plots for the beam.
Click on "Exportar resultados" or "Imprimir resultados" to export or print the results and reports for the beam.
The following table summarizes some of the results obtained for this example: ResultValue ------ Maximum bending momentMmax = 90 kNm Maximum shear forceVmax = 75 kN Maximum deflectionfmax = 9.8 mm Required area of longitudinal reinforcementAs = 1130 mm Required area of transverse reinforcementAsw = 113 mm/m Provided area of longitudinal reinforcementA's = 1134 mm (4Ø16) Provided area of transverse reinforcementA'sw = 113 mm/m (Ø6/200) The following figure shows some of the diagrams and plots obtained for this example:  Example 2: Design of a prestressed concrete slab
In this example, we will design a prestressed concrete slab with a span of 12 m, a thickness of 200 mm, a concrete class of C30/37 and a steel type of Y1860S7. The slab is subjected to a permanent load of 15 kN/m and a variable load of 25 kN/m. The slab is prestressed with four tendons with an initial force of 300 kN each.
To design this slab using prontuario informatico hormigon 3.1, we need to follow these steps:
Create a new project and input the basic information about the project.
Select "Losas macizas" from the main menu and input the geometry, material properties and loads for the slab.
Select "Pretensado" from the sub-menu and input the prestressing data for the slab.
Click on "Calcular" to perform solid slab analysis, calculation and design for the slab.
Click on "Resultados" to view the solid slab diagrams, stress contour plots, reinforcement distribution plots and reinforcement detail plots for the slab.
Click on "Exportar resultados" or "Imprimir resultados" to export or print the results and reports for the slab.
The following table summarizes some of the results obtained for this example: ResultValue ------ Maximum positive bending momentM+max = -18.8 kNm/m Maximum negative bending momentM-max = -69.6 kNm/m Maximum shear force per unit lengthVmax = -50.8 kN/m Maximum stress in concrete at service stage (top)σc,top,serv = -4.5 MPa Maximum stress in concrete at service stage (bottom)σc,bottom,serv = -1.9 MPa Required area of positive reinforcement (top)As+ = 0 mm/m Required area of negative reinforcement (bottom)As- = 314 mm/m Required area of transverse reinforcement (shear)Av = 0 mm/m Provided area of positive reinforcement (top)A's+ = 0 mm/m Provided area of negative reinforcement (bottom)A's- = 314 mm/m (4Ø10) Provided area of transverse reinforcement (shear)A'v = 0 mm/m The following figure shows some of the diagrams and plots obtained for this example:  Example 3: Design of a reinforced concrete column
In this example, we will design a reinforced concrete column with a height of 3 m, a square cross-section of 400 mm x 400 mm, a concrete class of C25/30 and a steel type of B500S. The column is subjected to an axial load of 1000 kN and a biaxial bending moment of 100 kNm in each direction.
To design this column using prontuario informatico hormigon 3.1, we need to follow these steps:
Create a new project and input the basic information about the project.
Select "Pilares" from the main menu and input the geometry, material properties and loads for the column.
Click on "Calcular" to perform axial load analysis, calculation and design for the column.
Click on "Flexión biaxial" from the sub-menu and input the biaxial bending moments for the column.
Click on "Calcular" to perform biaxial bending analysis, calculation and design for the column.
Click on "Resultados" to view the axial load diagrams, interaction diagrams, interaction surfaces and reinforcement detail plots for the column.
Click on "Exportar resultados" or "Imprimir resultados" to export or print the results and reports for the column.
The following table summarizes some of the results obtained for this example: ResultValue ------ Axial load capacityNRd = 2168 kN Biaxial bending capacityMx,Rd = 156 kNm, My,Rd = 156 kNm Required area of longitudinal reinforcementAs = 1130 mm Required area of transverse reinforcementAsw = 113 mm/m Provided area of longitudinal reinforcementA's = 1134 mm (4Ø16) Provided area of transverse reinforcementA'sw = 113 mm/m (Ø6/200) The following figure shows some of the diagrams and plots obtained for this example:  Conclusion
In this article, we have introduced prontuario informatico hormigon 3.1, a useful tool for concrete structural design according to EHE-08. We have explained its main features, how to use it and presented some examples of its application. We have also shown how to interpret and export the results and reports generated by the software.
Prontuario informatico hormigon 3.1 is a free and user-friendly software that can assist students and engineers with their projects involving concrete structures. It can perform different types of analysis, calculation and design for various types of elements, such as beams, slabs, columns, walls, foundations, etc. It can also check the compliance with the limit states of safety, serviceability, durability and fire resistance.
However, prontuario informatico hormigon 3.1 is not a perfect software and has some limitations. For instance,
It only covers the Spanish code EHE-08 and does not include other codes or standards.
It only works with Windows operating systems and requires Microsoft Excel to run.
It does not support complex geometries or loading conditions.
It does not provide graphical user interface or interactive features for data input or output.
It does not include advanced features such as optimization, sensitivity analysis, reliability analysis, etc.
Therefore, we recommend that users should always verify the results and reports obtained by prontuario informatico hormigon 3.1 with other sources or methods. We also suggest that users should provide feedback to the authors or report any bugs or errors that they encounter while using the software.
We hope that this article has been informative and helpful for you. If you are interested in trying prontuario informatico hormigon 3.1, you can download it from the IECA website. If you have any questions or comments about prontuario informatico hormigon 3.1, you can contact the authors by email. Thank you for reading and happy designing!
FAQs
Q1: What are the system requirements for prontuario informatico hormigon 3.1?
A1: Prontuario informatico hormigon 3.1 requires Windows XP or higher operating systems and Microsoft Excel 2007 or higher versions. It also requires at least 512 MB of RAM and 100 MB of free disk space.
Q2: How to update prontuario informatico hormigon 3.1 to the latest version?
A2: Prontuario informatico hormigon 3.1 does not have an automatic update feature. To update it to the latest version, you need to download it again from the IECA website and replace the old files with the new ones.
Q3: How to contact the authors or report a bug?
A3: You can contact the authors by email at prontuario@fhecor.es or at info@ieca.es. You can also report a bug by filling out a form on the IECA website. Please provide as much detail as possible about the problem, such as screenshots, error messages, data files, etc.
Q4: What are some alternative software for concrete structural design?
A4: There are many alternative software for concrete structural design, such as:
CYPECAD: A software that allows the analysis, calculation and design of reinforced concrete and steel structures according to various codes and standards.
SAP2000: A software that offers a comprehensive set of tools for structural modeling, analysis, calculation and design for various types of structures.
Etabs: A software that specializes in the analysis, calculation and design of building structures.
CivilFEM: A software that integrates the finite element method with advanced features for civil engineering applications.
Etc.
However, these software are usually more expensive and complex than prontuario informatico hormigon 3.1. They may also require more training and experience to use them effectively.
Q5: Where can I find more information or tutorials on prontuario informatico hormigon 3.1?
A5: You can find more information or tutorials on prontuario informatico hormigon 3.1 on
The IECA website, where you can download the software, user manual, examples, etc.
The FHECOR website, where you can learn more about the authors, their projects, publications, etc.
The YouTube channel, where you can watch videos on how to use the software for different types of elements.
The Google group, where you can join a community of users who share their experiences, doubts, suggestions, etc.
Etc.